Skip to content
English
  • There are no suggestions because the search field is empty.

How to Connect Binsr to Your Customer Portal for Automated Review Requests

Connect your Binsr account once and every completed inspection automatically sends your client a review request by email and text. Setup takes about two minutes.

If you run your inspections in Binsr and use WolfPack Review Requests, you can connect the two yourself from your Customer Portal. Once connected, marking an inspection complete in Binsr is all it takes: your client gets a review request without anyone on your team lifting a finger.

This article covers what you need before you start, how to connect, what happens after each inspection, and how to fix the connection if it ever stops working.

Heads up: This connection sends review requests only. It requires the Review Requests service to be active on your account. If you are not sure whether it is, ask your WolfPack specialist team.


Before you start

You need two things:

  • A Binsr API key. You create this in your Binsr account (steps below).
  • Billing access on your Customer Portal login. Only users with billing access can connect or change an integration. Everyone else can see the Binsr tile but will get the message "Ask your account admin to change this."

How to connect Binsr

  1. In Binsr, go to API, then API Keys, and create a new key. Copy it.
  2. Log in to your Customer Portal and click Integrations in the left menu, under Company.
  3. Under Scheduling software, find Binsr and click Set up.
  4. Paste your key into the Binsr API key field.
  5. Optional: enter a Send delay (minutes). This is how long after the inspection is completed the request goes out. Leave it blank, or enter 0, to send right away.
  6. Click Connect.

When the tile shows Connected, you are done. Your portal sets up the link inside Binsr for you, so there is nothing else to configure on the Binsr side.

Tip: The send delay is in minutes and can be anything up to 10080 (7 days). A few common choices: 60 for one hour, 120 for two hours, 1440 for the next day. A delay gives your client time to read the report before the request arrives.


What happens after each inspection

When an inspection is marked completed in Binsr, your portal creates a review request for each client on that inspection, using the name, email address, and phone number saved in Binsr.

  • Only your clients are asked. Agents on the inspection never receive a review request from this connection.
  • Timing follows your send delay. With no delay, the request goes out within about a minute of the inspection being completed. With a delay, the clock starts when the inspection was completed.
  • The client needs an email address or phone number in Binsr. A client with neither is skipped.
  • It works going forward. Inspections you completed before connecting are not picked up.

From there, the request works exactly like any other WolfPack review request: the same messages, the same reminder, and the same results in your Reviews tab. See Review Requests: How Automated Review Requests Work for what your client sees.

The usual protections still apply

A request from Binsr follows the same rules as every other request, so no one is over-asked:

  • Anyone on your Do Not Send List is never sent a request.
  • A client who already gave feedback on an earlier request is not asked again.
  • A client who received a request in the last 30 days is not asked again yet.

A request that is skipped for one of these reasons is never sent and never counted for billing.

If you have more than one location

If your account has multiple review locations, each Binsr request is matched to a location using the inspection address, following the routing choice in your Reviews settings.


Managing your connection

Once Binsr is connected, the button on the tile changes to Manage. From there you can:

  • Change the send delay or replace the API key, then click Save changes.
  • Test connection to confirm your portal can still reach Binsr.
  • Disconnect to remove the connection and your saved key.

You can also use the switch on the Binsr tile to turn the connection off for a while without removing it.


Troubleshooting

What you see What it means What to do
"Binsr didn't accept that API key. Check it and try again." The key was mistyped, incomplete, or deleted in Binsr. Copy the key again from Binsr under API, then API Keys, and paste it in fresh.
"We couldn't reach Binsr. Try again in a minute." A temporary connection problem. Wait a minute and click Connect or Test connection again.
The tile shows Needs attention Binsr is no longer accepting the saved key, usually because the key was deleted or replaced in Binsr. Completed inspections will not send review requests until this is fixed. Click Manage, enter a current API key, click Save changes, then Test connection.
The tile shows Connected but requests are not appearing Binsr may not be notifying your portal when inspections are completed. Click Manage, open Technical details, and copy the Webhook URL. In Binsr, go to API, then Webhooks, and add that URL with the event inspection.completed.

Heads up: One Binsr account connects to one Customer Portal account. If you run more than one company out of the same Binsr account, talk to your specialist team before connecting.


Frequently asked questions

Does this cost extra? There is no separate charge for the connection. Requests sent through Binsr count the same as any other review request on your plan.

Will my agents get review requests? No. Only the clients on the inspection are asked.

What if a client should never be asked? Add their email address or phone number to your Do Not Send List under Reviews, then Settings. The Review Requests article linked below walks through it.

Can I still send a request by hand? Yes. Connecting Binsr does not change anything else. You can still create a one-time request from the Reviews tab for a job that did not go through Binsr.

What happens if I disconnect? Completed inspections stop creating review requests. Requests that were already sent, and your review results, are not affected.

I use different scheduling software. Can I connect it? The Integrations page lists every connection available for your account, along with the ones that are coming soon. If yours is not there, let your specialist team know.


Questions?

Reach out to your WolfPack specialist team through your Customer Portal or by replying to any email from the team.

Related articles: Review Requests: How Automated Review Requests Work · How to Add or Remove Team Members in Your Customer Portal · How to Update Your Personal Settings and Notification Preferences in Your Customer Portal